維修衡器：地磅測試可用三位半數字萬用表分別測量每一個傳感器的輸出端看其數字是否穩定，如果有其中一個或幾個信號輸出不穩定，則可進下一步檢查；如果每個傳感器信號輸出都比較穩定，沒有明顯的不穩定現象，也可將顯示器的分度值改小（如：原來d=20(50)kg改成d=5kg)再分別對每只傳感器進行擺脫檢查，如果擺脫某一只傳感器儀表跳變，說明被擺脫的傳感器或及其連接線有問題。第三步：抽出輸出信號不穩定的傳感器連接線，查看連接線是否有擠壓痕跡，是否有鼠咬或銳器導致破損現象，如果有以上現象可對受擠壓或破損處進行處理。處理方法：將受損處外層線皮撥開對內層導線逐一查看，如需重新連接的應進行錫焊連接，對內線有線芯的應用防水防潮膠帶逐一包扎，內線包扎后要再對破損處外皮進行保護性包扎，以防線口再次受潮引起跳變。如果連接線處理后跳變，就說明問題得到處理，如果儀表還繼續跳變，說明傳感器損壞應于更換。

汽車衡地秤定期維修：對數字式地磅檢查接線盒進水或受潮、連接線有破口以及傳感器損壞造成跳變的方法及處理步驟如下：步，在顯示器上進人各個傳感器點輸出檢査，査看各個傳感器點輸出是否正常，如果每個傳感器都有不正常跳變，可檢查接線盒是否有進水或受潮現象，如果接線盒有進水或受潮現象可先用電吹風對接線盒進行吹干處理。吹干后如果跳變，就說明問題得到處理，如果儀表還繼續跳變，可檢查接線盒與顯示器連接線是否有破損現象，如果有破損現象可按5.6中的‘第三步’進行處理，處理后應顯示正常。第二步如果某個傳感器顯示輸出顯示不穩定，也要按5.6中的‘第三步’進行處理。